You may have to Search all our reviewed books and magazines, click the sign up button below to create a free account.
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, and plate up to 1.000 inch (25.40 mm) in nominal thickness (see 8.7). AMS5869D updates chemical testing requirements (3.1), adds requirements for heat treatment (3.3), prohibits unauthorized exceptions (1.1, 3.4.1.3, 3.7, 4.4, 5.1.1, 8.6, 8.7), allows prior revisions (8.8), and results from a Five-Year Review and update of this specification.
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of corrosion and heat resistant steels, iron alloys, titanium, and titanium alloys ordered to inch dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range.
This specification covers a corrosion- and heat-resistant alloy in the form of sheet, strip, and plate. AMS5874D is the result of a Five-Year Review and update of the specification. The revision updates composition testing and reporting (see 3.1 and 3.1.1), invokes a new specification for sheet finish (see 3.2.1), adds pyrometry controls and requirements for continuous heat treatment (see 3.3 and 3.3.1), adds strain rate control during tensile testing (see 3.4.2.1), allows incremental loading during testing (see 3.4.5.2), updates tolerances (see 3.6), prohibits unauthorized exceptions (see 3.7, 4.5.1, 5.1.1, and 8.5), adds country of origin requirements (see 4.5), and allows prior revisions (see 8.4).
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, and plate 0.010 to 2.000 inches (0.25 to 50.80 mm), inclusive, in nominal thickness (see 8.5). AMS5870F prohibits unauthorized exceptions (3.6), revises properties (3.3), reports (4.4) and identification (5.1.1), and results from a Five-Year Review and update of this specification.
This specification covers a corrosion and heat-resistant nickel alloy in the form of round, square, and flat wire 0.625 inch (15.88 mm) and under in nominal diameter or thickness capability tested in a Spring Temper condition. AMS5699H is the result of a Five-Year Review and update of the specification. The revision includes an update to the Title, Scope and Response to Heat Treatment (1.1, 3.3.4) to clarify the purchased condition, prohibits unauthorized exceptions (3.3.5, 3.6, 4.4.2, 5.2.3, 8.7), updates composition reporting (3.1.1), adds continuous heat treatment and pyrometry control (3.2), clarifies reduction requirements (3.2.2, 3.2.3) adds strain rate requirements for tensile testings (3.3.1), adds country of origin requirements (4.4.1), updates definitions (8.4), and allows prior revisions (8.6).
This specification covers a corrosion and heat resistant nickel alloy in the form of sheet, strip, and plate from 0.010 to 1.000 inch (0.25 to 25.40 mm) in thickness. AMS5597H is the result of a Five-Year Review and update of the specification. The revision incorporates size limits (1.1, 3.5.3), updates heat treatment requirement 3.4, adds strain rate for tensile tests (3.5.1.1.1, 3.5.2.1), prohibits unauthorized exceptions (3.9, 4.4.1, 5.1.1, 8.6), and allows prior revisions (8.7).
This specification covers a corrosion- and heat-resistant nickel-based alloy in the form of sheet, strip, and plate 0.020 to 2.25 inches (0.50 to 57.2 mm) in thickness. AMS5951B is the result of a Five-Year Review and update of the specification. The revision increases the allowable thickness (see 1.1 and throughout), revises composition specification and reporting (see 3.1 and 3.1.1), updates the solution heat treatment (see 3.4.1 and 3.4.2), adds option for continuous heat treatment (see 3.4.3), limits Table 2 testing requirements, updates Table 4 grain size based on thickness, adds mechanical properties for thicker sections (see Table 5 and Table 6), adds strain rate controls for tensile tests (see 3.5.1.1.1 and 3.5.2.1.1), prohibits unauthorized exceptions (see 3.5.3, 3.8, 4.4.4, 5.1.1, and 8.5), and allows prior revisions (see 8.4).
This specification covers established manufacturing tolerances applicable to sheet, strip, and plate of corrosion and heat resistant steels, iron alloys, titanium, and titanium alloys ordered to metric dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of a specified range.